エラー表示一覧

ラクトコーダT-Tの内部エラー

110	Invalid value in the input
111	Input canceled by input keyboard
112	Password: Length longer than allowed on display
113	Division / divided by 0
114	Overflow of a variable or arrays occurred

傾きセンサーエラー

150	Inclinationsensor is not calibrated
151	Inclination: at testing higher than limits in EEPROM
152	Inclination higher than 30 -> close the panel (blind/diaphragm)

EEPROMエラー

170	Checksum in EEPROM not ok
171	Wrong value of EEPROMs

内部/外部フラッシュメモリ

190	In the flash is not the right identifier

外部RAM

195

RAM error

測定エラー

200	Max. duration of measurement exceeded
201	Invalid measurement state (variable measurement state)
202	Error at emptying the LC-TT at the end of the measurement

ステップモーター

250

Shutter motor (diaphragm) loses more than BM_MAX_LOST_STEPS,the blind/diaphragm no longer turns correctly 対処法 E250はオリフィスディスクの回転が引っ掛かっているため発生するエラーです。解決方法：① ラクトコーダ本体のインレットヘッドを外す ② 測定チェンバーに湯を入れてゆすぐ。 ③ <7>サービス -＞ <3>テスト -> <5>ダイヤフラムテストを実行する ④ オリフィスディスクの回転を確認する。 説明動画URL https://www.youtube.com/shorts/qt9wTMqRWV4

サンプリングエラー

270	Engine of sampling could not be brought to the defined position
271	Sampling overrided (too many samplings ==> sample bottle full)

真空ポンプ

280	Vacuum-engine could not be brought to the defined position

USBエラー

300	Error accessing the USB stick
301	Filesystem is not linked, can not be used
302	Desired directory does not exist
303	Error while changing the directory
304	Wrong or no file type specified
305	Temporary path not available for access to USB stick
306	Error deleting the USB task
307	Error deleting the KHCI-task (this task is generated by the USB task)
308	Error initializing the MFS file system of the USB interface
309	Error with parameters for USB-Communication (usb-kom of type t-USB-Data)
310	No file extension found
311	Error writing to LAST_BD.txt
312	Too many files of the searched file type
313	The line that was read contains no data
314	Timeout occurred while reading the USB stick
315	Error opening the file
316	Error closing the file
317	No data in the USB data array
318	Error initializing the USB pointer
319	Error while allocating the abs_path-pointer
320	No more storage space in teh MFS-file-system
321	At ﾂｫdir / youﾂｻ command was no more file to be found
322	File-Pointer not valid
323	Error while setting the file cursor
324	Error creating a new folder
325	Pointer-error absolut pointer and/or file pointer
326	Error initializing the USB task
327	Error writing to the USB stick
328	USB-test: read file does not match to written content

バッテリーエラー

360	Akku voltage in impermissible range

HW-Version

380	AD-value in impermissible range

群データエラー

500	No operating data / no herd data file available
501	No operating data found (ID for BD (herd data) not available
502	Wrong operating data format
503	Checksum of the operating data is wrong
504	Max. number of animals per farm exceeded
505	Too many files in the folder with herd data (number defined in usb_io.h)

測定データエラー

600	Error in the format/size in the measured value range
601	MW_RAM full, no space for further measurement
602	Interlinking of measured values incorrect
603	Error of the checksum of the management area of the measured values
604	Linking of measured values defective, offset from measured values to the next is no longer correct
605	Measured value RAM contains milking data, delete from MW-RAM not allowed
606	Error while reading pointer

オンライン測定エラー

620	Error in the format/size in the online measurement area
621	ONL_MW_RAM full, no room for further online measurement
622	Interlinking of online measured values incorrect
623	Error checksum of the management area of online measurement values
624	Interlinking of the online measured values is defective, offset from online measured values to the next one is not correct anymore

コマンダーエラー

700	Not allowed with b_probe_status_betrieb == PROBE_NR_COMMANDER
701	No sampling status defined
702	Invalid specification of how to read the sample-ID at Commander measurement

Akku / I2C-Extern

800	I2C-interface 1 not activated
801	Timeout during communication with I2C interface 1

RTC / EEPROM / 傾きセンサー

810	I2C-interface 1 not activated
811	Timeout at communication with I2C-interface 1
812	Mutex not available

RCT

900	Invalid datas/values read by RTC

プリンターエラー

1000	Characters/signs on the UART could not be sent
1001	Timeout reading a UART-interface
1002	Answer available, but wrong answer
1003	Error in the checksum oft he transmitted data
1004	Unknown error code received back
1005	Air bubble detection failed
1006	Error executing the bubble detection command
1007	No communication with print module
1008	No sieve put into the LC-TT
1009	Firmware-version is not correct
1010	NOK failed

無線モジュールエラー

1020	Characters/signs on the UART could not be sent
1021	Timeout reading a UART interface
1022	Answer available, but wrong start sign of the answer
1023	Error in the checksum of the transmitted data
1024	Not received the desired number of bytes when reading from radio module
1025	Error at start address when reading the data
1026	Error during echo test (wrong character/wrong sign)
1027	Communication error with the radio module (general error)
1028	Wrong data type requested by the radio module
1029	No configuration data announced by the radio module
1030	Data does not start with the start character @
1031	Firmware-version is not correct
1032	Invalid RFID address in the FM

トランスポンダモジュールエラー

キャリブレーション

1040	Characters/signs on the UART could not be sent
1041	Timeout reading a UART interface
1042	Answer available, but wrong start sign of the answer
1043	Error in the checksum of the transmitted data
1044	Communication error with the transponder module (general error)
1045	No transponder module installed
1046	Firmware-version is not correct

バーコードリーダー

1050	No barcode reader installed, but was required

QSPI (Display / serial Flash)

1060	Timeout sending with the QSPI

シリアルフラッシュ

1070	Overflow in the Flash
1071	Too many characters/signs received
1072	Wrong value read

パラレルフラッシュ

1080	Value that was written is not identical to the value read
1081	When deleting or programming, a timeout has arisen

洗浄エラー

1100	Max. duration of cleaning exceeded

プログラム更新エラー

1200	The identifier is not correct
1201	Error in the header of the Update-File
1202	Error in the checksum of the update file
1203	Error in the concatenation of the peripheral header
1204	Unknown periphery
1205	Too many peripheral updates

バーチャル個体による測定

1300	No online data for the virtual measurement
1301	The virtual data is too long for the measured value RAM
1302	Too many files in the virtual data folder

キャリブレーション

1400	The offset of the LC-TT is not calibrated
1401	The difference between the lower and upper offset during the offset calibration is too large

一般警報

10001	Desired text can not be shown in the display or characters are not available in the font
10002	No picture found for the picture number
10003	Reading stopped by Flag End of File
10004	Function was canceled by the user
10005	LC-TT is emptied, the liquid has not yet completely drained
10006	RAM for online values full, Measurement is not necessarily terminated
10007	Warning that no USB stick is plugged in (check for hidden service menu)
10008	Timeout while waiting for user input
10009	End measurement
10010	Config data is invalid
10011	Config data is invalid because the time in it is not plausible
10012	Config data is invalid because wrong animal species is loaded
10013	Config data is invalid because the validity period has expired
10014	Config data is invalid because the checksum is wrong
10015	New format/size detected in service buffer
10016	Unknown value in a switch case statement